GUIDE®QUICK START Model: TAR HL-005-004, SL-004-004, MSA-004-004Release: 1.2.00 / Updated: 09.19.08 Threat Analysis Reporter
6 8e6 ThreaT analysis reporTer Quick sTarT GuideRack Mount the ServerRack Setup PrecautionsWarning:Before rack mounting the server, the physical envi
8e6 ThreaT analysis reporTer Quick sTarT Guide 7 Rack Mount Instructions for HL ServersRack Setup SuggestionsDetermine the placement of each componen
8 8e6 ThreaT analysis reporTer Quick sTarT GuideLocking Tabs: Both chassis rails have a locking tab, which serves two functions. The rst is to lock
8e6 ThreaT analysis reporTer Quick sTarT Guide 9 Install the Server into the Rack You should now have rails attached to both the chassis and the rack
10 8e6 ThreaT analysis reporTer Quick sTarT GuideInstall the Server into a Telco Rack If you are installing the 8e6 server unit into a Telco type rac
8e6 ThreaT analysis reporTer Quick sTarT Guide 11 Rack Mount Instructions for SL ServersRack Setup SuggestionsDetermine the placement of each compone
12 8e6 ThreaT analysis reporTer Quick sTarT GuideInstall the Slide Assemblies to the Rack1. After you have installed the short and long brackets to
8e6 ThreaT analysis reporTer Quick sTarT Guide 13 Install the Chassis into the Rack1. Push the inner slides, which are attached to the chassis, into
14 8e6 ThreaT analysis reporTer Quick sTarT GuideRack Mount Instructions for MSA ServersOptional: Install the Chassis RailsNOTE: If your chassis
8e6 ThreaT analysis reporTer Quick sTarT Guide 15 3. Locate the three holes on each side of the chassis and locate the three correspond-ing holes on
ii 8e6 ThreaT analysis reporTer Quick sTarT Guide8e6 ThreaT analysis reporTer Quick sTarT Guide© 2008 8e6 Technologies. All rights reserved. This doc
16 8e6 ThreaT analysis reporTer Quick sTarT GuideOptional: Install the Traditional UP RacksAfter you have installed the inner rails on the chassis, y
8e6 ThreaT analysis reporTer Quick sTarT Guide 17 7. Slide the chassis into the rack as shown below.NOTE: The chassis may not slide into the rack sm
18 8e6 ThreaT analysis reporTer Quick sTarT GuideOptional: Install the Open RacksAfter you have installed the inner rails on the chassis, you are rea
8e6 ThreaT analysis reporTer Quick sTarT Guide 19 3. Attach the front (short) bracket to the front end of the rack, and secure it to the rack with t
20 8e6 ThreaT analysis reporTer Quick sTarT Guide5. Measure the depth of your rack and adjust the length of the rails accordingly. Then, secure the
8e6 ThreaT analysis reporTer Quick sTarT Guide 21 Install the Chassis into the RackCAUTION: Before installing the chassis into the rack:• Make sure
22 8e6 ThreaT analysis reporTer Quick sTarT GuideInstall the SL or HL Server BezelAfter rack mounting an SL or HL server, the bezel should be install
8e6 ThreaT analysis reporTer Quick sTarT Guide 23 Check the Power SupplyThis server is equipped with a universal power supply that handles 100-240 V,
24 8e6 ThreaT analysis reporTer Quick sTarT GuideGeneral Safety InformationServer Operation and Maintenance PrecautionsWarning:Observe the following
8e6 ThreaT analysis reporTer Quick sTarT Guide 25 Do not expose the server to rain or use near water. If liquids of any kind should leak into the cha
8e6 ThreaT analysis reporTer Quick sTarT Guide iii Contentsthreat analysis reporter introduCtion ...
26 8e6 ThreaT analysis reporTer Quick sTarT GuideMotherboard Battery Precautions Caution:The battery on the motherboard should not be replaced withou
8e6 ThreaT analysis reporTer Quick sTarT Guide 27 install the serverStep 1: Initial Setup ProceduresThis step requires you to link the workstation to
28 8e6 ThreaT analysis reporTer Quick sTarT GuideStep 1A: Quick Start Setup ProceduresLink the Workstation to the Threat Analysis ReporterMonitor and
8e6 ThreaT analysis reporTer Quick sTarT Guide 29 Fig. 3 - Diagram of SL chassis front panel, power button at far rightFig. 4 - Diagram of MSA chassi
30 8e6 ThreaT analysis reporTer Quick sTarT GuideHyperTerminal Setup ProceduresIf using a serial console, follow these procedures to create a HyperTe
8e6 ThreaT analysis reporTer Quick sTarT Guide 31 C. At the Connect using eld, select the COM port assigned to the serial port on the laptop (proba
32 8e6 ThreaT analysis reporTer Quick sTarT GuideF. In the HyperTerminal session window, go to File > Properties to open the Properties dialog bo
8e6 ThreaT analysis reporTer Quick sTarT Guide 33 Quick Start menu instructionsFor these Quick Start setup procedures, you will need your network adm
34 8e6 ThreaT analysis reporTer Quick sTarT GuideE. At the Press the number of your selection prompt, press 2 to display the Adminis-trator Password
8e6 ThreaT analysis reporTer Quick sTarT Guide 35 Congure Network Interface screenA. At the Enter interface lan1 IP address eld, enter the IP addr
iv 8e6 ThreaT analysis reporTer Quick sTarT Guide
36 8e6 ThreaT analysis reporTer Quick sTarT GuideC. Press Y for “Yes” to conrm and save your entries for the LAN1 interface, and to go to the next
8e6 ThreaT analysis reporTer Quick sTarT Guide 37 Congure default gateway screenA. At the Enter default gateway IP eld, enter the IP address for t
38 8e6 ThreaT analysis reporTer Quick sTarT Guide B. At the Enter (optional) second DNS server IP eld, if you have a secondary Do-main Name Server
8e6 ThreaT analysis reporTer Quick sTarT Guide 39 B. Press Y for “Yes” to conrm and save your entry for the host name, and to go to the Time zone r
40 8e6 ThreaT analysis reporTer Quick sTarT GuideCongure Wizard user screenA. At the Enter wizard user name eld, enter the username that will be u
8e6 ThreaT analysis reporTer Quick sTarT Guide 41 Quick Start Setup conrmation screenPress Y for “Yes” to save all your Quick Start setup entries an
42 8e6 ThreaT analysis reporTer Quick sTarT GuideSystem Status screenThe System Status screen contains the following information:lan1 interface for w
8e6 ThreaT analysis reporTer Quick sTarT Guide 43 Physically Connect the Unit to the NetworkAfter performing initial setup procedures for the Threat
44 8e6 ThreaT analysis reporTer Quick sTarT GuideStep 1B: LCD Panel Setup ProceduresOn an SL or HL unit, the Threat Analysis Reporter can be congure
8e6 ThreaT analysis reporTer Quick sTarT Guide 45 Reboot >Shutdown >NOTE: Navigation tips in the 8e6 menu: • Use the up / down arrow key to sc
8e6 ThreaT analysis reporTer Quick sTarT Guide 1 threat analysis reporter introduCtionThank you for choosing to evaluate the 8e6 Technologies Threat
46 8e6 ThreaT analysis reporTer Quick sTarT GuideGatewayWhen the Gateway option is selected, the Gateway screen displays with the Congure Gateway IP
8e6 ThreaT analysis reporTer Quick sTarT Guide 47 C. Press the checkmark key to return to the previous screen.D. Press the “X” key to return to the
48 8e6 ThreaT analysis reporTer Quick sTarT GuideShutdownWhen the Shutdown option is selected, the Shutdown screen displays with two menu items.A. C
8e6 ThreaT analysis reporTer Quick sTarT Guide 49 LCD ControlsWhen the LCD Controls option is selected, the LCD Controls screen displays with the fol
50 8e6 ThreaT analysis reporTer Quick sTarT GuideStep 2: Wizard Setup ProceduresFor this step, you will need your network administrator to provide yo
8e6 ThreaT analysis reporTer Quick sTarT Guide 51 D. After reading the End User License Agreement, you have the option to do either of the following
52 8e6 ThreaT analysis reporTer Quick sTarT GuideWizard Step 1: Register administratorStep 1 is performed in the left side of the rst screen of the
8e6 ThreaT analysis reporTer Quick sTarT Guide 53 D. Click the [+] Add tab below to open the IP Range Information dialog box: E. Enter the Bandwidt
54 8e6 ThreaT analysis reporTer Quick sTarT Guide To modify an IP address range, double-click the entry in the list box to highlight it and to displ
8e6 ThreaT analysis reporTer Quick sTarT Guide 55 Wizard Step 2: Register R3000 & ERStep 2 is performed in the right side of the rst screen of t
2 8e6 ThreaT analysis reporTer Quick sTarT GuideAbout this DocumentThis document is divided into the following sections:Introduction - This section i
56 8e6 ThreaT analysis reporTer Quick sTarT GuideE. Click OK to close the dialog box and to display your entries in the list box: NOTE: Additional R
8e6 ThreaT analysis reporTer Quick sTarT Guide 57 To modify the IP address and Server Name for the R3000 server, click the [+] Add tab to re-open the
58 8e6 ThreaT analysis reporTer Quick sTarT GuideER:Respond to the question “Do you have an Enterprise Reporter?” by clicking the radio button corres
8e6 ThreaT analysis reporTer Quick sTarT Guide 59 Step 3: Server SettingsStep 3, the following R3000 server information displays: SMTP Server Setting
60 8e6 ThreaT analysis reporTer Quick sTarT Guideled indiCators and ButtonsSL and MSA UnitsFront LED Indicators and Buttons for Hardware Status Monit
8e6 ThreaT analysis reporTer Quick sTarT Guide 61 HL Unit Front LED Indicators and Buttons for Hardware Status MonitoringOn an HL unit, the following
62 8e6 ThreaT analysis reporTer Quick sTarT GuideRear LED Indicators for Hardware Status MonitoringUID (LED indicator) – On the rear of the HL chassi
8e6 ThreaT analysis reporTer Quick sTarT Guide 63 HL and SL UnitsFront LED Indicators for Software and Hardware Status MonitoringOn an HL or SL unit,
64 8e6 ThreaT analysis reporTer Quick sTarT Guideregulatory speCifiCations and disClaimersDeclaration of the Manufacturer or ImporterSafety Complianc
8e6 ThreaT analysis reporTer Quick sTarT Guide 65 Electromagnetic Compatibility Class A NoticeIndustry Canada Equipment Standard for Digital Equipmen
8e6 ThreaT analysis reporTer Quick sTarT Guide 3 serviCe informationThe user should not attempt any maintenance or service on the unit beyond the pro
66 8e6 ThreaT analysis reporTer Quick sTarT GuideEC Declaration of ConformityEuropean Community Directives Requirement (CE)Declaration of ConformityM
8e6 ThreaT analysis reporTer Quick sTarT Guide 67 Tap insTallaTionappendix: optional ethernet tap installationThis appendix pertains to the optional
68 8e6 ThreaT analysis reporTer Quick sTarT GuideTap insTallaTionInstall the Ethernet Tap UnitDiagram showing TAR Ethernet Tap installation on the ne
8e6 ThreaT analysis reporTer Quick sTarT Guide 69 Tap insTallaTionC. Using a crossover cable, connect one end to the Switch’s port congured to be t
70 8e6 ThreaT analysis reporTer Quick sTarT GuideindexBBSMI 64, 65CChange Quick Start password 41crossover cable 67, 69EEMC 64, 66FFCC 64HHL 1,
8e6 ThreaT analysis reporTer Quick sTarT Guide 71 RR3000 1, 27, 42, 50, 55, 56, 57, 68, 69Rack Setup Precautions 6RAID 1, 63reboot 45, 47RoHS com
8e6 Corporate Headquarters (USA): 828 West Taft Avenue Orange, CA 92865-4232 • Tel: 714.282.6111 or 888.786.7999 Fax: 714.282.6116 (Sales/Technical Su
4 8e6 ThreaT analysis reporTer Quick sTarT Guidepreliminary setup proCeduresUnpack the Unit from the CartonInspect the packaging container for eviden
8e6 ThreaT analysis reporTer Quick sTarT Guide 5 Select a Site for the ServerThe server operates reliably within normal ofce environmental limits. S
Commentaires sur ces manuels